Header image  
   
 
 
             

 

Home

About PEC

Leadership

Membership

Member's Only

Chapters

Upcoming Events

MATHCOUNTS

Bridge Building

Education Foundation

Engineer's Week

National Organization

Contact Us


 
 
 

  

Bridge Building Contest Rules

These rules have been developed for the 2007 40th Annual Colorado High School Bridge Building Contest to be held on Saturday February 24th 2007 at Bureau of Reclamation Engineering and Research Laboratories, Building 56 at the Denver Federal Center. Questions about these rules should be directed to John Migliaccio at jmigliaccio@jrengineering.com. The object of this contest is to see who can design, construct and test the most efficient bridge within the following specifications. Note: Check these specifications as well as the posted Questions and Answers continually for critical changes, clarifications, additional requirements, tips, etc.

Model bridges are intended to be simplified versions of real-world bridges, which are designed to accept a load in any position and permit the load to travel across the entire bridge. In order to allow the contest to proceed in a reasonable amount of time only one loading position is actually tested.

2007 Colorado Bridge Building Contest Specifications

1. Materials

  1. The bridges must be constructed only from 3/32-inch square cross-section basswood and any commonly available adhesive. This PEC website lists several suppliers of the basswood.
  2. The basswood may be notched, cut, sanded or laminated in any manner but must still be identifiable as the original basswood.
  3. No other materials may be used. The bridge may not be stained, painted, or coated in any fashion with any foreign substance.

2. Construction

  1. The bridge mass shall be no greater than 25.00 grams.
  2. The bridge (see Figure 1) must span a gap (S) of 300 mm, be no longer (L) than 400 mm, have a maximum width (W) of 80 mm, and be no taller (H) than 200 mm above the support surfaces.
  3. No portion of the bridge shall extend below the top of the support surfaces. (This applies to the un-loaded condition. Deflections below the support surface under loading will be permitted.)
  4. The loading lanes (P) shall be horizontal and shall lie on the physical top of the bridge between 100. mm and 200. mm above the support surfaces. Loading planes shall be 50 mm x 50 mm minimum.
  5. The bridge must be constructed to provide support for the loading plate (see Section 3 below) at each of the two loading points. Any portion of the structure above or below the loading plane must provide clearance for the loading rod at the two locations of the loading plate.
  6. The bridge construction does not need to be symmetric.

3. Loading

  1. The load will be applied downwards (from above) by means of a 50 mm square plate (see Figure 2) resting on the loading plane of the bridge. The plate will be attached to the rod from above to the center of the plate. The bottom plate surface will be horizontal and shall not pivot during the loading.
  2. The two edges of the loading plate will be parallel to the longitudinal axis of the bridge at the time of load application (i.e., the loading plate will not be rotated in order to allow the plate to be supported).
  3. The loading will be applied at one of two loading points, located as follows:
    At "A1" or "A2" located 50 mm to either the left or right of the centerline.
  4. Bridges must have loading planes at both locations (A1 and A2) and shall be capable of bearing load at either plate.

4. Testing

  1. On the day of the contest the judges will decide the loading location to be used (right or left side of testing machine). The same location will be used for all bridges. Students may choose which loading plate bears the load during testing and may orient their bridges accordingly in the testing mechanism.
  2. The bridge will be centered on the support surfaces
  3. The loading plate will be located on the bridge and the load will be steadily applied from above the bridge onto the specified loading location.
  4. The load will be increased until failure occurs.
  5. Failure is defined as the inability of the bridge to carry additional load or a load plate deflection of 25 mm, whichever occurs first.
  6. The bridge with the highest structural efficiency, E, will be the winner, where;

     

    Load supported in grams
    E = -----------------------------------
    Mass of bridge in grams

5. Qualification

  1. All construction and material requirements will be checked prior to testing by the judges. Bridges that fail to meet these specifications at the conclusion of the allowable time for checking will be disqualified. Bridges disqualified prior to the start of the contest may be tested as exhibition bridges at the discretion of the builder and the contest directors.
  2. If, during testing, a condition becomes apparent (i.e., use of ineligible materials, inability to support the loading plate, etc.) which prevents testing as described above in Section 4, that bridge shall be disqualified. If the disqualified bridge can accommodate loading, it may still be tested as an exhibition bridge as stated above.
  3. The decisions of the judges will be final. These rules may be revised as experience shows the need (please check the Professional Engineers of Colorado Bridge Building web site at http://www.pec.org/bridgebuild/contest.shtml periodically after October 31, 2006.)

 


  
 
 

 

 

 

 

 

    
   

 

Professional Engineers of Colorado
3030 W 81st Avenue
Westminster, CO  80031
Phone: 303-480-1160
Fax: 303-458-0002